-
Rear Short Stroke ShocksWe now offer 3 different levels of Rear Short Stroke Shocks to fit your budget and specific driving needs! Now….what’s the difference in these 3 damper choices? I’m sure it can seem a bit confusing with so many options...$245.00 -
Panhard / Lateral Bar for TA22 CelicaWe designed these to the highest possible standards. No skimping on the expensive parts here. All Heim joints at both ends with metric sizes for a direct fit! Zero Slop, and Zero Deflection - this lateral rod is SUPER tight! This rod has enough...$215.00 -
DIY Outer Tie Rod Kit with Bumpsteer Adjustment.These are the same custom Outer Tie Rods we've been offering for the AE86 and other cars for years now! We use very strong 5/8" bore rod ends with 3/4" shanks for these parts. The Rod Ends are 3-piece teflon lined to keep them quiet and long...$205.00 -
Evolved Roll Center Adjusters for 85mm Toyota StrutsMeet our new Evolved RCA's for the AE86 and all other 85mm strut spacing Toyotas! Using very clever geometry and hardware, these units can be used as a normal Roll Center Adjuster, Ackermann Adjust Roll Center Adjuster or Negative Camber Roll Center...$180.00 -
T3 x Swift Japan Springs PairSwift is a high end manufacturer of coil springs from Japan and provides top quality products. Swift's Springs are wound with less coil than competitors allowing for more stroke and reduced weight! Noticeable increase in traction, smoother...$180.00 -
HyperCo Helper Spring KitDo you like to run your car low and deal with an excessive amount of droop that unseats the springs? Or maybe you're just tired of hearing a clunk when 3 wheeling out of driveways. Our new HyperCo Helper Spring Kit is the perfect solution for these...$150.00 -
HyperCo Coilover SpringsHyperCo Coilover Springs are the top choice of winning race car drivers and drifters worldwide! Proven in Indy, IMSA, and F1 to perform consistently, season after season. Advanced metallurgy, spring winding, and heat treating techniques...$145.00 -
Camber Plate Upper Hat SystemThe Camber Plate Upper Hat System is available for any car using coilovers. It can also be utilized with most other camber plates on the market, including Cusco and Cusco-Clone camber plates.$105.00 -
Riser Blocks for Camber PlatesIf you are using our camber plates and need a little more height, these riser blocks are the ticket. These gold blocks click into place between the camber plate bearing block and the camber plate, giving 1" additional height. These will work with...$95.00 -
Steering Coupler for the TA22 CelicaThe original steering column on the TA22 Celica includes a rubber "rag joint" between the U-joints. This can cause a vague and un-responsive steering feel. This billet aluminum steering coupler will drastically improve the steering feel and feedback of...$85.00 -
GTX2 Steering StopsThese Steering Stop add-ons for our GTX2 Front Lower Control Arms are a simple solution to prevent your steering from over-centering. Laser Cut Mild Steel Powder Coated Grey Adjustable Stoppers All Hardware included$45.00 -
Conical Upper Hats for Coilovers with 2.5" ID springsSold in Pairs. Machined Aluminum conical upper hats for use on DIY coilovers. Specifically designed for use with 2.5" ID coilover springs. Center bore is 22mm. If you are ordering our weld on coilover kit, you do NOT need to order these separately...$45.00
Evolved Front Crossmember for the Datsun 510
We're excited to introduce you to our Evolved Crossmember for the Datsun 510!
Our good friend, Steve Coleman, is a longtime 510 guy with a wealth of knowledge and massive parts collection. He...
$795.00